The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain
the code label.
A Template ......................................... 1 Sheet
B LAN connector cover ...........................1 pc.
C Safety wire ........................................... 1 pc.
D Wire lug fixing screw
M3 × 10 mm {3/8 inches} ................... 2 pcs.
(of them, 1 for spare)
E Safety wire lug .....................................1 pc.
F Auxiliary handle ....................................1 pc.
G Desiccant .........................................1 Sheet
H Waterproof tape ...................................1 pc.
Turn off each system’s power supply before making a connection. Before making connections,
prepare the required peripheral devices and cables.
IMPORTANT:
●Use all 4 pairs (8 pins) of the Ethernet cable (category 5e or better, straight).
●The maximum cable length is 100 m {328 feet}.
●Make sure that the PoE device in use is compliant with IEEE802.3af standard.
●When the Ethernet cable is disconnected once, reconnect the cable after around 2
seconds. When the cable is quickly reconnected, the power may not be supplied
from the PoE device.
●When cables are used outdoors, there is a chance that they may be affected by light-
ning. In this case, install a lightning arrester just before where the Ethernet cable
connects to the camera.
Connect an Ethernet cable (category 5e or better, straight)
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with
cables exposed or installing it under the eaves.
The camera body is waterproof, but
the cable ends are not waterproof.
Be sure to use the supplied
waterproof tape at the points where
the cables are connected to apply
waterproof treatment in the following
procedure.
Failure to observe this or use of
a tape other than the provided
waterproof tape (such as a vinyl tape)
may cause water leakage resulting in malfunction.
When connecting to a network using a PoE hub
Before starting the installation, check the entire system conguration.
The following illustration gives a wiring example of how to connect the camera to the network via
a PoE device (hub).
Stretch the tape to
approx. twice its length.
2×
IMPORTANT:
●The adjustment monitor is used to adjust the field of view when installing or servicing
the camera. It is not provided for recording/monitoring use.
●Depending on the adjustment monitor, some characters (camera title, preset ID, etc.)
may not be displayed on the screen.
●Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
The hook engages
with the connector
terminal
LAN connector cover
(
B
: accessory)
*1 SDXC/SDHC/SD memory card is described as SD memory card.*2 Depending on the scanning application used, the Data Matrix may not beable to be read correctly. In this case, access the site by directly entering thefollowing URL.
●When the camera is able to communicate with theLights orange
connected device
LINK indicator
●When data is being sent via the network cameraBlinks green (accessing)
ACT indicator
●When AF (Auto Focus) operation is being executed
Blinks red (about once per second)
●When the camera is being startedLights red
●When an SD memory card
*1
is recognized normally
Lights red → Lights off
●When the SD memory card slot is not used or an abnormality Lights red → Stays red
is detected in SD memory card after the camera has started
SD ERROR/AF indicator
●When an SD memory card is inserted and couldLights off → Blinks green →
be recognizedLights off
●When data can be saved after the SD memory card is inserted Lights off → Lights green
and the SD ON/OFF button is pressed (for less than 1 second)
●When data can be saved to the SD memory cardLights green
●When the SD memory card is removed after holding down
Lights green → Blinks green →
the SD ON/OFF button for about 2 seconds Lights off (recording)
Lights green →
Lights off (waiting for recording)
●When data cannot be saved to the SD memory card because Lights off
an abnormality was detected or the SD memory card is
configured not to be used
SD MOUNT indicator
● How to initialize the camera
Follow the steps below to initialize the network camera.
1 Turn o the power of the camera. When using a PoE hub, disconnect the Ethernet cable from the
camera.
2
Turn on the power of the camera while holding down the INITIAL SET button, and keep the INITIAL
SET button held down till the SD MOUNT indicator is lit in green (more than 10 seconds). In about
2 minutes after releasing the INITIAL SET button, the camera will start up and the settings including
the network settings will be initialized.
● When the INITIAL SET button (i.e. the initializing button) is pressed (less than 1 second) to switch
the output signal of the MONITOR OUT terminal (NTSC
PAL output), the MONITOR OUT terminal
can be switched for the NTSC monitor/PAL monitor.
IMPORTANT:
●When the camera is initialized, the settings including the network settings will be initialized.
Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.
●Before initializing the settings, it is recommended to write down the settings in advance.
●Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
INITIAL SET button (Initializing / NTSC
PAL switch button)
1 When the SD ON/OFF button is pressed for less than 1 second, the SD MOUNT indicator is lit
green and data can be saved to the SD memory card.
2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator goes
out, and the SD memory card can be removed.
SD ON/OFF button
TILT lock screw
Camera
Front cover
Safety wire (C: accessory)
Sunshield
Camera mount
bracket
Camera Arm
PAN lock screw
[2] Remove the front cover
Installation
Step 1 Before starting the installation
The installation tasks are explained using 5 steps.
Tear off the blue tape attached on camera arm before installing the camera.
Prepare the required parts for installation method before starting the installation. The following is the requirements for the installation method.Installation methodRecommended screwMinimum pull-out strengthDirectly mount the camera onto the ceiling or wall (when there is a space for wiring in the ceiling or the wall)M4 screws × 3724 N {163 lbf} (per 1 pc.)
*1
*1 To mount the camera onto the ceiling or wall, the safety wire (C: accessory)
must be attached. Have an M6 bolt and nut or anchor (with the minimum pull-out strength of 724 N {163 lbf}) ready for securing the safety wire.Step 1
Before starting the
installation
Step 2
Preparation
Step 3
Fixing the camera
Step 4
Adjusting the camera
Step 5
Congure the network
settings
IMPORTANT:
●For the screws or anchor bolts used in the above method, be sure to secure the mini-
mum pull-out strength of 724 N {163 lbf} per screw or bolt.
●Select screws according to the material of the ceiling or wall that the camera will be
mounted to. In this case, wood screws and nails should not be used.
●If a ceiling or wall board such as plaster board is too weak to support the total weight,
the area shall be sufficiently reinforced.
●Because the front cover is temporarily removed when installing or adjusting the camera,
make sure no liquid enters the camera at these times.
Loosen the 4 front cover fixing screws, and then remove the front cover.
1
Pass the safety wire (
C
: accessory)
through the wire mounting hole in the safety wire lug (E
:
accessory).
Wire mounting hole
Front cover fixing screws
Front cover
[1]Attaching the safety wire
Step 2 Preparation
Safety wire lug
(
E
: accessory)
Safety wire
(
C
: accessory)
Wire fitting
Wire lug fixing screw
(
D
: accessory)
Safety wire lug
(
E
: accessory)
2 Fit the Safety wire lug to the camera.Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}* The safety wire is not shown in thesubsequent illustrations.
YAW lock screw
Name plate
Zoom knob
MONITOR OUT jack
(Video Out terminal
Default:
For NTSC monitor)
SD memory card slot
IR LED
Ver el manual de Panasonic WV-SPW532L aquí, gratis. Este manual pertenece a la categoría Cámaras de seguridad y ha sido calificado por 1 personas con un promedio de 7.5 . Este manual está disponible en los siguientes idiomas: Inglés . ¿Tienes alguna pregunta sobre Panasonic WV-SPW532L o necesitas ayuda? Haz tu pregunta aquí
¿Necesitas ayuda?
¿Tiene alguna consulta sobre el Panasonic y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Panasonic proporcionarle una buena respuesta.
¿No puede encontrar la respuesta a su consulta en el manual? Puede encontrar la respuesta a su consulta en las preguntas frecuentes sobre el Panasonic WV-SPW532L más abajo.
¿El manual de Panasonic WV-SPW532L está disponible en Español?
Por desgracia, no tenemos el manual de Panasonic WV-SPW532L disponible en Español. Este manual está disponible en Inglés.
¿Necesitas ayuda?
¿Tiene alguna consulta sobre el Panasonic y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Panasonic proporcionarle una buena respuesta.
Número de preguntas: 0